These are all list of error code in Canon iR/iR more to come, i hope your machines works fine and never get error. E Main cause. fixing oil, the error code is indicated. E The rated voltage of the power supply and that of the fixing unit do not match. E Clock pulses fail to be generated. canon ir is showing an error codes E How it will solve? Your error code is for the fixing unit solve by checking the follwoing: 1. Fixing lamp.
|Published (Last):||14 August 2010|
|PDF File Size:||19.69 Mb|
|ePub File Size:||14.35 Mb|
|Price:||Free* [*Free Regsitration Required]|
The scanning lamp xenon tube is faulty. Main Cause The stapler home position detecting switch MS7 errr faulty. The communication line has an opencircuit. The coin vendor is faulty. Mode ofDetection The guide home position sensor does not turn on when the guidemotor has been driven for about 0. The paper folding homeposition sensor PI21S is faulty. The saddle stitcher controllerPCB is faulty. The hard disk drive is faulty.
The saddle stitch controllerPCB is faulty. The folding motor M2S is faulty. The stapler shift motor M4 is faulty.
Canon iR5000 Service Manual: Error Codes; List Of Error Codes
The ADF V power supply isfaulty. The stitch motor rear, M6S is faulty. Main Cause The connector is not connected properly. The swing guideclosed detecting switch ir000 MS6 is faulty. Mode ofDetection Communication between the height sensor and the finisher controllerPCB is not possible, or communication data has an error. The potential measurement PCB is faulty. Main cause The LAN card is faulty.
The laser scanner motor M15 is faulty. Mode of Detection When the inlet cover, front cover, and the delivery cover are foundto be closed, the inlet door switch detects an open condition for 1sec or more from the start of the initial rotation of the host machineor the start of printing. The lamp inverter PCB is faulty.
The paper push-onplate motor M8S is faulty. The copy data controller or the remote diagnostic device is faulty. The DC power supply fan FM6 is faulty.
The finisher vode PCB is faulty. The wiring is faulty short circuit,open circuit. The punch motor M1P is faulty. The scanner HP sensor PS39 is faulty. The waste toner feedscrew is faulty.
Crazy About Copiers Loading Mode ofDetection The paper push-on plate home position sensor does not turn onwhen the paper push-on plate motor has been driven for 0. The saddle stitcher controller PCB is faulty.
Error Codes > Canon > iR > page 1
errkr The copy data controller PCB is faulty. The fixing motor M19 is faulty. Mode ofDetection The stapler does not leave home position when the stapler motorhas been driven for 0. Main Cause The delivery motor clock sensor PI10 is faulty. Mode ofDetection The alignment plate does not leave home position when the alignmentmotor has been driven for eeror secs. The feed fan FM1 isfaulty. The fixing web length sensor PS45 is faulty.
Mode ofDetection An error has occurred in the communication between the various.
Main Cause The shutter open sensor PI5 is faulty. After replacing the fixing web, be sure to reset the two web counters in service mode: Main Cause The hard disk fan FM7 is faulty. The delivery motor M2 is faulty.
The swing guide open sensor PI18 is faulty. Mode ofDetection The communication between the host machine and the finisher hasbeen interrupted; this error is detected by the host machine. Mode ofDetection The stapler unit does not leave home position when the stapler shiftmotor has been driven for 4 secs. Newer Post Older Post Home.
The reader controller PCB is faulty. The paper push-on platehome position sensor PI14S is faulty. The paper push-on plate leadingedge position sensor PI15S is faulty. Main Cause The swing motor clock sensor PI20 is faulty.
Mode ofDetection While the primary charging assembly cooling fan is being driven.